Home > Service Error > Service Error 149.00 Lexmark

Service Error 149.00 Lexmark

Buy the Full Version You're Reading a Free Preview Pages 638 to 834 are not shown in this preview. Observe the lamp through the left near side of the printer. When you have added an incompatible application to the computer, it can cause Service Error 149.00 Lexmark, another reason will be a non-functional driver. Requires further measurement The printhead (laser scanner) does not contain any serviceable parts. navigate here

Reconnect. Error 921 Fuser is below standby temperature when idle. Error 928 Erase lamp assembly missing or disconnected Error 929 The toner sensor is not operating properly, the developer drive assembly is not operating properly or the print cartridge is See “Network Wrap Tests” on page 23. have a peek at this web-site

Error 58 Duplex Not Attached Duplex is electrically connected but no longer mechanically attached, and printer top cover is closed. Replacement of the thermistor is not a cost effective repair, replace fuser assembly. PrintCopy .infoservice Service manual Parts List Error Code Equivalency Sign In Contacts About Us Service manual Error Code Parts List Equivalency Complete information for maintenance and repair printers, copiers,

  • If you want to learn technical skills but don't want to spend some bucks, then executing the trouble shooting process by yourself will really be advantageous.
  • Can be system board or printhead.
  • Check Toner Sensor Check Cable Check System Board Check developer drive for worn, loose or broken parts.
  • Additional info on X and XX codes available by email.

These usually happen when browsing the web. Check paper sensor flag for restricted movement or damage. Error 7X Network Card Codes These user codes are documented in various network card user manuals. Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time.

Replace the bump alignment motor Replace bump motor Replace interlock switch Replace System Card Error 230 Paper Jam - Check Duplex The paper is most likely jammed in the Duplex In the Control Panel, just go to System and click Security. Restore password × Upload manual upload from disk upload from url Thank you for your help! × AdBlocker Detected! New service manuals Canon LBP712Cx, (sm, pc), Eng, 36.2Mb Canon MF412dw, (sm, pc), Eng, 30.6Mb Canon imageCLASS LBP251dw, (sm, pc), Eng, 20.5Mb HP LaserJet M527dn Enterprise, (srm, stm, pc), Eng, 46.1Mb

More Info Sign In Upload Page of 659 Go Download Table of ContentsContents Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Comment Manuals Brands Lexmark Manuals Printer MS81x You need to understand that there are times where downloaded files are not functional so you have to cope with it. Check AC power source for noise. Most cost effective solution is to replace the fuser Lexmark Fuser Pricing Error 927 Main Fan Stalled, Cartridge Fan or RIP fan stalled, Power off and manually spin fan - it

Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed. http://comphelp.org/guide/service-error-149-00-lexmark/ email with model, primary and secondary pattern for troubleshooting info. Install more memory Simplify print job Delete fonts, macros and other data stored in RAM Error 39 Page too complex to print.To verify that the printer recognizes all the installed memory, If one of these errors appeared during POST, or while the printer was idle (not printing or receiving data), or while trying to print one of the internal test pages, replace

Whenever your RAM is too low, this problem might also happen. http://softbb.net/service-error/service-error-305-verizon.html To print the manual completely, please, download it. Engine Board 3. Replace low voltage power supply assembly.

Ads are the only way to keep ManualsLib FREE and keep it growing. Yes, I'll Whitelist Cancel CompHelp - Menu Skip to content Home Service Error 149.00 Lexmark Posted on June 2, 2015 by admin ZDNet's Ultimate Black Friday 2009: Deals, steals & specials Indicates that the fuser is below standby temperature when the printer is idle. his comment is here Make sure top access door is closed securely 2.

Generated Tue, 06 Dec 2016 16:52:04 GMT by s_wx1200 (squid/3.5.20) The product was delivered just a few minutes ago. Error 53 Unformatted or Defective Flash - Flash problem at POR or while attempting to write.

Shop for Lexmark print cartridges Error 32 32 Wrong Print Cartridge installed The installed print cartridge is not supported by the Optra printer.

Error 80 Network Card Codes These user codes are documented in various network card user manuals. Run the Quick Disk Test. Check the wiring harness cable. Perform fuser service check.

The fuser assembly is subject to mechanical wear and heat related degradation and is a scheduled replacement item in most machines at between 200K and 350K pages. To verify that the printer recognizes all the installed memory, go to the user menus and print the “Print Menus” test page. Note: This error indicates the printer was able to read the cartridge ID, but the ID did not pass the verification test. http://softbb.net/service-error/service-error-409.html Check fan for binding or defective bearing - Replace Fan How did we do?

Fuser errors can be from a cold fuser or an overheated fuser. If the tray is difficult to remove, then you may have to remove the tray above or below tray X to remove the jammed pages. Error 26 Duplex unit is installed but paper tray is not sensed. Error 923 Fuser is too hot while printing or when idle. • Short in the thermistor circuit. • Noisy thermistor signal • Fuser is actually overheating due to hardware faults.

The system returned: (22) Invalid argument The remote host or network may be down. Also, can I get some instructions on putting in the rollers. A 920 error caused by low line voltage can sometimes be cleared by turning the machine off and then on again. Intterconnect Board Error 940-943 Color Machines Toner Metering Cycle failure CMKY cartridge 940 = Cyan cartridge 941 = Magenta cartridge 942 = Yellow cartridge 943 = Black cartridge Toner metering cycle

I am new to this and do not want to screw this up. Replace Printhead Pricing Error 931 Printhead error - No first sync - check connections at both ends of cable for corrosion or oxidation. Check printhead, cable, motor, system board. Some problems might get worse over time.

Reload the paper and do a power on reset. Press "GO" to clear message and temporarily continue Install OPC Belt/Photo Developer Error 84 Transfer Drum Exhausted The Transfer drum has reached the end of it's life and must be Verify latch relay is operating - slowly close door and listen for interlock switch 3. Remove and reinstall print cartridge.

Error 59 Duplex Cover Open Top cover of duplex unit is sensed open. See “Duplex” on page 2-16 Error 24 The defined paper size is too short to print data as formatted. Roller is approximately 2" in circumference print defects with this repetitive spacing can be caused by transfer roller problems, on a standard 11" page defect would repeat five times. Jump to error 92X Some Lexmark printers have indicator lights which indicate by solid, blinking or off, an error condition.

John D. If an open circuit, replace the lamp or fuser. Error 901 Engine Flash Indicates the Flash with the system code program is defective Replace System Board Request Quote Error 914 DC Pick Motor - No Encoder Feedback Check the